Merit Network
Can't find what you're looking for? Search the Mail Archives.
  About Merit   Services   Network   Resources & Support   Network Research   News   Events   Home

Discussion Communities: Merit Network Email List Archives

North American Network Operators Group

Date Prev | Date Next | Date Index | Thread Index | Author Index | Historical

Re: Data Center Wiring Standards

  • From: Mark Foster
  • Date: Fri Sep 08 21:27:44 2006

My thoughts go like this:  We put a patch panel in each rack.  Each of
these patch panels is permanently (more or less) wired to a patch panel in
our main patch cabinet.  So, essentially what you've got is a main patch
cabinet with a patch panel that corresponds to a patch panel in each other
cabinet.  Making connection is cinchy and only requires 3-6 foot
off-the-shelf cables.

Does that sound more correct?

I talked to someone else in the office here, and they believe that they've
seen it done with a switch in each cabinet, although they couldn't
remember is there was a patch panel as well.  If you're running 802.1q
trunks between a bunch of switches (no patch-panels needed), I can see
that working too, I suppose.

Any standards?  Best practices?  Suggestions?  Resources, in the form of
books, web pages, RFCs, or white papers?
Theres a series of ISO Standard for data cabling but nothing is yet set in stone around datacentres. I think the issue of Standards in datacentres was touched on here some time back?

Ok, a quick google later,

TIA-942 Telecommunications Infrastructure Standards for Data Centres covers off a lot of the details. Its pretty new and I don't know if its fully ratified yet?

I quote...

--8<--
Based on existing cabling standards, TIA-942 covers cabling distances, pathways and labeling requirements, but also touches upon site selection, demarcation points, building security and electrical considerations. As the first standard to specifically address data centres, TIA-942 is a valuable tool for the proper design, installation and management of data centre cabling.

The standard provides specifications for pathways, spaces and cabling media, recognizing copper cabling, multi-mode and single-mode fiber, and 75-ohm coaxial cable. However, much of TIA-942 deals with facility specifications. For each space within a data centre, the standard defines equipment planning and placement based on a hierarchical star topology for backbone and horizontal cabling. The standard also includes specifications for arranging equipment and racks in an alternating pattern to create žhotÓ and žcoldÓ aisles, which helps airflow and cooling efficiency.

To assist in the design of a new data centre and to evaluate the reliability of an existing data centre, TIA-942 incorporates a tier classification, with each tier outlining guidelines for equipment, power, cooling and redundant components. These guide-lines are then tied to expectations for the data centre to maintain service without interruption.

--8<--

The source url for the above was http://www.networkcablingmag.ca/index.php?option=com_content&task=view&id=432&Itemid=2. You may like to see if you can track down a copy of the referenced standard.


From my personal POV -

You have a couple of options depending on your switching infrastructure and required cabling density - and bandwidth requirements. One way would be to have a decent switch at the top of each cabinet along with a Fibre tie to your core patch / switching cabinet. All devices in that rack feed into the local switch, which could be VLAN'd as required to cater for ILO or any other IP management requirements. Uplink would be a trunk of 1000SX, 1000LX, MultiLink Trunk combinations of same, or perhaps even 10Gig Fibre.

The other option would be to preconfigure each rack with a coupla rackunits of fixed copper or fibre ties to a core cabinet and just patch things around as you need to. Useful if you are in a situation where bringing as much as possible direct into your core switch is appropriate, and cheaper from a network hardware pov - if not from a structure cabling pov.

Good luck. I know what a prick it is to inhereit someone elses shoddy cable work - I find myself accumulating lots of after-hours overtime, involving essentially ripping out everything and putting it all back _tidily_ - and hoping that I don't overlook some un-documented 'feature'...

Mark.




Discussion Communities


About Merit | Services | Network | Resources & Support | Network Research
News | Events | Contact | Site Map | Merit Network Home


Merit Network, Inc.